Tombstone Gun Grip Kits: www.TombstoneGrips.com - - Email: Dave@TombstoneGrips.com - -

****** Flat rate shipping for all items on the same order! USA +$15, International +$48. Bank Card processing adds 4% ******

Store Front Account Search Product List Basket Contents Checkout
Optional Sign In:

Specials
Screws,  Mounting Hardware
Medallions
Blank Rectangles, Spacers, & Grips
Spacers
Grip Blanks
Blocks
Grip Caps
Butt Plates


S&W 469 smooth, larger size
 
S&W 469 smooth, larger size Quantity in Basket: None
Code: sw_47e
Price: $58.00
Shipping Weight: 0.15 pounds
 
Select SOLID color ($10). Natural Ivory is no extra cost. For pearl effects, use PEARL option instead (Ivory = default)

:
Translucent/Pearl ($16 option). Do NOT select both SOLID and PEARL. (Pearl over-rides solid color choice)

:
Add a medallion ($14/pr):
Drill screw holes? (Send tracing for location):
Yes, drill holes (be sure to send accurate pattern for location)
No, do not drill the screw holes (be SURE you really want this option!)
Are you sending a tracing?:
YES! I want to assure proper size/shape. Tombstone is responsible for fit to tracing. Tracing will show hole pattern. **************************************
NO. I will be responsible if I choose the wrong size grip. I will measure my gun and compare to the listed specs. If I order a grip that is the wrong size or shape, I agree that it is NOT returnable. *****************************************************
I already mailed a tracing BEFORE I placed this order.
Optional note:
 
Quantity:
 
This is a grip kit for the S&W 469 having an extended area toward the hammer (top rear of grip). It is a larger grip than the 46g model, and is available with or without screw holes. If you want screw holes I will need a tracing or pattern with the hole location marked. It helps if you can tell me the size of the head and screw threads. These guns were built in several variations, some of which used two screws per panel and some used no screws but clamped the grip in place with the back strap and used snug spacers on the grip backs.

The grip kit comes with two grip spacers, which you may wish to epoxy glue to the back of the grips after fitting them into the frame cut-out on either side. Mount one grip and apply the epoxy-film side of the grip spacer through the grip frame. When the epoxy has cured, remove that grip panel and then do the same for the other side. Regular five-minute epoxy (two part glue in tubes, mix together and spread a film of it on the back of the spacer) works well if the back of the grip is cleaned with acetone first. This removes all fingerprints and oils. spacers

Here are the grip dimensions:
    Left Panel
  • Top width (uppermost section) = 0.7 inches
  • Flat from rear of the uppermost section to rear, before the slope begins, is 0.8 inches wide.
  • Front top notch is 0.3 inches tall and 0.4 inches wide.
  • Grip width from front edge to peak of the rear edge (maximum grip width) is 2.35 inches.
  • Width from the edge of the front top notch to the rear of the grip, measured parallel to the base, is 1.70 inches.
  • Width from the narrow portion at rear (where the web of your hand fits) to the front edge is 1.8 inches.
  • Width from mag release notch center to rear edge is 1.6 inches.
  • Width of projection below mag release notch to rear edge is 1.85 inches.
  • Width at 0.1 inch above the rear corner, just above the mainspring housing pin cut-out, to front edge is 1.7 inches
  • Width right at the rear corner (described above) to front edge = 1.68 inches.
  • Width of bottom flat = 1.3 inches.
  • Height of the grip from top most portion to base (at 90 degrees to base) = 3.75 inches
  • Height of the grip from top rear flat to base = 3.58 inches.


    Right Panel
  • Top flat width = 1.2 inches.
  • Width from front edge to the end of the rear flat area = 2.1 inches.
  • Width across the grip from front edge to projection of the "hammer" cover (widest part of the grip) = 2.3 inches.
  • Width from narrow portion of rear curve (web of hand area) to front edge = 1.65 inches.
  • Bottom swell width from front to back edge 1.8 inches.
  • Just above rear notch (mainspring housing pin cut-out) to front edge = 1.7 inches.
  • Flat base width = 1.25 inches.
  • Overall grip height measured 90 degrees to base = 3.70 inches.
  • Length of straight front edge from top to bottom, measured along the front edge = 3.9 inches.
    Thickness
  • Bottom center thickness = 0.3 inches
  • Top Center thickness = 0.2 inches




Related Item(s)
Code Name Price Availability  
SW_44d S&W Model 469 (44d) $58.00  
sw_46g S&W 469 smooth, smaller size $58.00  

Dave Corbin
Stock items (medallions, screws, specials) usually ship within 10 days.
I can't promise a specific ship date, as it will vary with circumstances.
If you can't wait, please don't order! I'm working as fast as possible.

Be SURE to read the TERMS of SALE page, so you KNOW what you are getting.

Credit Card Processing Center adds 4% to order total.


Home Page Colors Pearl effects Example Guns