|
Heritage RR Smooth (154a)
|
|
|
Quantity in Basket:
None
Code: Heritage_154a
Price: $68.00
Shipping Weight: 0.20 pounds
|
|
Smooth grips for the Heritage Rough Rider:
- (A)Front height = 1.1 inches
- (B)Overall height = 3.3 inches
- (C)Base Width = 2.4 inches
- (D)Front midpoint to rear edge = 1.6 inches
- Length of notch at top = .55 inches
- Depth of notch at top = 0.05 inches
- Width at 1.5 inches from base = 1.6 inches
- Thickness at base midpoint = 0.65 inches
- Thickness at top = 0.40 inches
This smooth set of grips is available either as a 3-piece
kit (to make 1-piece Colt style grips, held on by a
removable back strap) or 2-piece screw-mounted pair.
If you order the 2-piece screw mounted style, the screw
and mounting comes with the grips and will be installed
unless you request otherwise. If you select 2-piece mounting
with screw, and then check "send screw kit uninstalled" I will
send you the screws without making the holes or installing
the ferrule and nut.
If you should select 1-piece kit with spacer, instead of
the screw mount 2-piece kit, I will send you the two panels
and the spacer, so you can fit them to the gun. No holes
will be made in the grips and no screw provided. Whatever
you check on the screw install or not install doesn't
matter, as there is no screw with the 1-piece kit.
In other words, whatever you select near the top of the
list overrides any contradiction picked lower in the list.
If you want the screw kit installed, on the 2-piece screw
mounted version, then you need to send a tracing with the
screw hole location indicated accurately. This can vary
with different years of production and models. Usually the
standard SAA Colt location works, but if you don't send me
a tracing and I have to guess, I'll have to use the location
that works most of the time with most guns...no guarantee
that it will work with your particular gun since I have no
clue if your gun is the same as the ones I've fitted before
or not! Send the tracing, save the hassle of sending it
back with $8 shipping for a replacement! (That said, 90%
of the time the standard hole pattern works. You can gamble
with your money on the 10% chance that your gun has a
mainspring located right where the hole normally goes, if
you wish. Up to you. Don't yell at me if that happens and
you didn't send a tracing, though!)
If you send a pencil tracing, please don't send it by fax
or send a photocopy of it! Those methods can distort the
image and are not very useful. The original pencil tracing
on paper, sent by mail, is what really helps get the size
correct for your particular gun.
These grips can be used for a variety of other guns, as
they are taller in the top portion than most of the Colt
Single Action grips and just about the same otherwise. It
is not much of a job to remove material. Beats putting it
back on! Therefore, if you have a gun with grips that are
just a little bigger than most of the other Colt styled
Single Actions in the upper section, this set of grips
may well do the job with a little fitting and shaping.
One of the guns on which these grips may also work is
the Colt Frontier Scout (or any of the "Scout" models which
have the notched top section). Some have smaller frames.
There are other Fronter Scount grips here, which may fit
them better.
|
Related Item(s)
Code
|
Name
|
Price
|
Availability
|
|
Heritage_77a
|
Heritage Rough Rider 22 (77a)
|
$68.00
|
|
Heritage_145a
|
Heritage Rough RIder Stag (145a)
|
$75.00
|
|
Colt_28d
|
Colt Frontier SAA Stag (28d)
|
$75.00
|
|
Colt_27a
|
Colt Frontier Scout/Logo (27a)
|
$68.00
|
|
|